Lena Rivera
Behr Advanced DeckOver® is a high-quality resurfacer designed to breathe new life into weathered or cracked wood and concrete surfaces. It can be used on horizontal and vertical wood and composite surfaces such as decks, railings, porches, and boat docks. It can also be used on concrete surfaces such as pool decks, patios, and sidewalks. To apply Behr DeckOver on existing paint, the surface must first be cleaned and prepared. This includes filling in any nail holes and cracks, removing loose paint, and removing dirt, mildew, oil, and grease, and taping off any areas that should not be painted. Once the surface is prepared, the Behr Advanced DeckOver® coating can be applied using a roller, working from one end to the other and maintaining a wet edge to avoid lap marks. A second coat is typically recommended for optimum durability.
| Characteristics | Values |
|---|---|
| Purpose | To resurface existing wooden decks and fill in cracks and splinters, extending the life of the deck. |
| Recommended for | Properly prepared exterior weathered or cracked horizontal and vertical wood and concrete surfaces such as decks, railings, porches, and boat docks. |
| Not recommended for | Drivable surfaces such as garage floors and driveways. |
| Preparation | All surfaces must be clean, dry, and free of any dirt, oil, and grease before application. Replace rotting or unstable boards, remove loose splinters, and fill in any holes or cracks. Use a wood cleaner or stain stripper to remove mildew stains, dirt, oil, and grease. |
| Application | Use a roller with an extended handle to apply the first coat, maintaining a wet edge to avoid lap marks. Use a nylon/polyester brush for corners and areas where the roller can't reach. Stir the product thoroughly before use and occasionally during use to ensure an even consistency. |
| Coverage | Up to 75 sq. ft. per gallon in 2 coats. |
| Colors | Available in over 700 colors, with up to 1000 colors when tinted with BEHR DYNASTY™ & MARQUEE® Interior & Exterior One-Coat Hide Color Collection. |
| Coats | Two coats are recommended for optimum durability. |
| Dry Time | Approximately 4-6 hours between coats (check product label for specific instructions). |
Explore related products
What You'll Learn
Prepare the surface
Preparing the surface is the most important step in ensuring a successful Behr DeckOver application. Here is a step-by-step guide to preparing your surface:
Inspect and Repair:
Firstly, carefully inspect the deck for any loose screws, nails, or boards. Repair or replace any damaged or unstable components. This is crucial for ensuring a stable and secure surface for the DeckOver application.
Clean the Surface:
The deck surface must be thoroughly cleaned and prepared, free of any dirt, oil, grease, mildew, or peeling paint/stain. For wood surfaces, use a product like BEHR PREMIUM® NO. 63 All-In-One Wood Cleaner to remove mildew, dirt, oil, and grease. Follow this with a product like BEHR PREMIUM NO. 64 Wood Stain & Finish Stripper to remove loose wood fibers, peeling paint, or deteriorated coatings. On new wood, use NO. 63 to remove mill glaze and open the pores of the wood. Rinse thoroughly and allow the surface to dry completely before proceeding.
For concrete surfaces, avoid applying DeckOver to structurally weak areas or those subject to hydrostatic pressure above 8 psi. Clean and etch the concrete with a product like muriatic acid to achieve a proper profile. At the end of this step, your concrete surface should be clean, dry, and free of any chipped or flaking paint.
Fill Cracks and Holes:
Use the Advanced DeckOver® coating with a nylon/polyester brush to fill in any nail holes and cracks up to 1/4". For deeper holes and cracks, additional filling may be required to ensure a smooth and even surface.
Protect Surrounding Areas:
Use painter's tape to cover any deck surfaces, walls, or railings that you do not want coated in the DeckOver product. This ensures a clean finish and prevents accidental application in unwanted areas.
Stir the DeckOver Product:
Before application, stir the Behr Advanced DeckOver® thoroughly to ensure the consistency is even. The product is thick, so take the time to mix it well. Continue to mix the product occasionally throughout the application process to maintain a consistent mixture.
By following these steps, you will effectively prepare your surface for the Behr DeckOver application, setting yourself up for a successful and long-lasting finish.
Repairing Key Scratches: Using Touch-Up Paint Like a Pro
You may want to see also
Explore related products
Use painter's tape
When applying Behr DeckOver on top of existing paint, painter's tape is an important tool to use to ensure clean edges, a neat overall look, and less mess. Before you start, make sure the surface is clean, dry, and dust-free so that the tape sticks properly. Use a damp rag to wipe down the surface if necessary.
When you're ready to apply the tape, lay it onto the surface, pressing down as you go to prevent any bumps or bubbles. Be careful not to stretch the tape, as this can cause it to lift or break. Once the tape is in place, use a smooth edge like a putty knife or credit card to press the tape down firmly, paying particular attention to the edges to ensure that they are sealed properly and the paint doesn't seep underneath.
After you've finished taping, wait about 30 to 60 minutes before you start painting. If you notice that your tape isn't sticking properly, it may be due to dirt or moisture on the surface. Try cleaning the surface again with a damp rag or using a different type of tape that is better suited for textured surfaces.
Once you've completed your painting project, carefully remove the painter's tape. By using painter's tape correctly, you can achieve sharp, professional-looking paint lines and avoid the need for touch-ups.
Paint a Blue Jay: Easy Step-by-Step Guide
You may want to see also
Explore related products
Fill holes and cracks
To fill holes and cracks, you should first inspect the deck for any loose screws, nails, or boards and repair as needed. Next, you need to fill nail holes and cracks with the Behr Advanced DeckOver coating using a nylon/polyester brush before coating the deck. Cracks up to 1/4" can be completely filled in with the coating, but deeper holes and cracks may require additional filling.
It is important to clean the surface before applying the Behr Advanced DeckOver coating. For wood surfaces, use a product such as BEHR PREMIUM® NO. 63 All-In-One Wood Cleaner to remove mildew stains, dirt, oil, and grease. You can also use a product like BEHR PREMIUM NO. 64 Wood Stain & Finish Stripper to remove loose wood fibers, peeling paint/stain, or deteriorated coatings. On new wood, use NO. 63 to remove the mill glaze and open the pores of the wood. Rinse thoroughly and allow the surface to dry before coating.
For concrete surfaces, do not use the product on areas that are structurally weak or subject to hydrostatic pressure above 8 psi. Clean and etch the concrete surface with a product like muriatic acid to achieve a profile similar to 150-grit sandpaper. At the end of the prep, you should have a clean, dry surface free of any chipped or flaking paint.
Winter Home Makeover: Interior Painting Guide
You may want to see also
Explore related products
Apply the first coat
To apply the first coat of Behr Advanced DeckOver, start by pouring the product into a paint tray. Using a roller with an extended handle, begin at one end of the deck and work your way to the other, maintaining a wet edge to avoid lap marks. For best results, use a 1/2" roller cover. You can also use a nylon/polyester brush to cut in around railings and in corners where the roller cannot reach.
Before applying the first coat, it is important to properly prepare the surface. All surfaces must be clean, sound, dry, and free of any dirt, oil, and grease. For wood surfaces, replace rotting or unstable boards, remove loose splinters, and fill nail holes and cracks with Advanced DeckOver coating using a nylon/polyester brush. Remove mildew stains, dirt, oil, and grease with a product such as BEHR PREMIUM® NO. 63 All-In-One Wood Cleaner. If there is peeling paint or deteriorated coatings, use a product like BEHR PREMIUM NO. 64 Wood Stain & Finish Stripper to remove them. On new wood, use NO. 63 to remove mill glaze and open the pores of the wood. Rinse thoroughly and allow the surface to dry before coating.
For concrete surfaces, avoid applying DeckOver to areas that are structurally weak or subject to hydrostatic pressure above 8 psi. Clean and etch the concrete with a product like muriatic acid to achieve a similar profile to 150-grit sandpaper. At the end of the preparation, ensure you have a clean, dry surface free of any chipped or flaking paint.
Additionally, stir the Behr Advanced DeckOver thoroughly before use to ensure an even consistency, and mix it occasionally throughout the application process. Apply painters' tape to any areas you do not want to be coated, such as walls or railings, to ensure a clean finish.
Masking Off Slickscreen Audio for Painting: A Step-by-Step Guide
You may want to see also
Explore related products
Apply the second coat
After the first coat of Behr DeckOver has dried (after approximately 4-6 hours, but check the product label for specific instructions), you can apply the second coat. The second coat should be applied in the same manner as the first. Pour the Behr Advanced DeckOver coating into a paint tray and work a roller into the tray until it is fully loaded with coating. For best results, use a 1/2" roller cover.
For a more textured look, use a Behr Premium Extra Textured Roller Cover with Advanced DeckOver Textured Coating. You can also use a brush or 1/4" nap roller for a smoother finish. If you want to use a 3/4" nap roller, keep in mind that the drying time will be longer. Apply the second coat, starting at one end and working your way to the other, ensuring you maintain a wet edge to avoid lap marks.
Use a nylon/polyester brush to cut in around railings and in corners where the roller can't reach. You can also use an airless sprayer that is properly sized for the product. When applying the second coat, make sure that the material, surface, and air temperatures are between 50 and 90 degrees Fahrenheit.
Editing Text in Paint: Keep the Background Intact
You may want to see also
Frequently asked questions
All surfaces must be clean, sound, dry, and free of any dirt, oil, and grease before application. Replace rotting or unstable boards and remove loose splinters. Remove mildew stains, dirt, oil, and grease with a product such as BEHR PREMIUM® NO. 63 All-In-One Wood Cleaner. You can also use a pressure washer or a hose with a high-pressure nozzle to remove any loose paint, dirt, or mildew.
You will need a roller with an extended handle, a paint tray, and a nylon/polyester brush to cut in around railings and in corners. You may also use an airless sprayer that is properly sized for the product.
Pour the Behr Advanced DeckOver® into a paint tray. Start at one end and work your way to the other, ensuring you maintain a wet edge to avoid lap marks. Cut in around railings and in corners where the roller can't reach.
Wait for the first coat to dry (approximately 4-6 hours, but check the product label for specific instructions), and then apply the second coat in the same manner as the first.
Yes, Behr Advanced DeckOver® can be applied over existing paint. However, it is important to remove any loose paint and ensure that the surface is properly prepared before application.
